Air filters · Type 06 of 08

High-temperature filters

A high-temperature filter is a deep-pleat filter built from materials that keep their shape and their seal when the air is hot. A standard filter has a plastic or wood frame, a synthetic media and an adhesive that soften or burn at modest temperatures. A high-temperature filter uses glass fibre media, metal separators between the pleats, a steel frame and a high-temperature seal.

Drawing
AKS-AF-HIGH-TEMPERATURE
Sheet
12 / 17
Rev
2026-11-16
Cross-section of a high-temperature filterAIRFLOWDHSTEEL FRAMEDEEP PLEATSSECTION A–A · HIGH-TEMPERATURE
Section through a high-temperature filter. Deep pleats of glass fibre media are held apart by metal separators inside a steel frame. The metal parts keep the pack open and rigid in hot air, and the seal is chosen for the operating temperature.

Construction

How a high-temperature filter is built.

Specify the operating temperature, and say whether it is continuous or an occasional peak. It is the most important line in the enquiry, because the correct frame, the media and the seal all depend on it. We do not quote a rating here, because it belongs to the exact product, and we confirm the exact rating for your order before you buy.

High-temperature filters at a glance
ConstructionDeep-pleat glass fibre media, metal separators, steel frame
SealChosen for the operating temperature, not a standard gasket
What we need firstThe continuous operating temperature and any peak
RatingWe confirm the exact rating for your order
What we need from youSize, class, temperature, how the filter is sealed, quantity

Performance and care

What to expect, and how to look after it.

Performance and limits

Metal separators hold the pleats open and let the hot air move through the pack without distortion. The steel frame resists warping, and it matters that the housing is built for the same temperature, because the filter is only as good as its seat. Thermal expansion also affects the seal, so the frame and the housing should be compared before the order.

Fitting and replacement

Hot air can also be dirty or moist. Oil mist, resin and condensate can coat the media and shorten its life, so mention the process in the enquiry. Do not clean a high-temperature filter with water or compressed air. Replace it when the pressure drop reaches its limit or when the seal fails.

Where it is used

Where high-temperature filters are used.

  • Industrial ovens and curing lines

    The supply and recirculation air of drying, baking and curing ovens needs a filter that does not melt or burn.

  • Paint drying and powder coating

    Hot air in the drying stage carries dust that would mark the finish, and the filter must survive the temperature.

  • Sterilisation tunnels and depyrogenation in pharmaceutical production

    Hot, filtered air that must stay clean at temperature.

  • Glass, ceramics and metal heat treatment

    Furnace and kiln areas where ordinary frames, gaskets and adhesives would fail.

  • Bakeries and food baking lines

    Hot supply air in ovens and proofing areas, with a frame and seal that suit the temperature.

Choosing

This type, or a different one.

Choose it when

Choose a high-temperature filter when the air is hot enough to soften or burn a standard filter: drying and curing ovens, baking lines, sterilisation tunnels, furnace areas.

Choose another type when

Choose a standard panel, bag or HEPA filter when the air is at ordinary ventilation temperature, and a metal filter when you want a washable coarse stage in warm, greasy or dirty air.

How to specify

Four details are enough to price a filter.

Send these four and a person can check the request. If one is missing, send what you have: a photo of the old filter and its label often fills the gaps.

  1. 01

    Size

    Width × height × depth in millimetres, for example 592 × 592 × 292. Measure the frame of the old filter or the opening it sits in. If the old filter has been squeezed into its slot, measure the slot. Standard and custom sizes are both possible, so send exact figures.

  2. 02

    Class

    Tell us the class you need (ISO 16890 or EN 1822). If your paperwork uses the older EN 779 names, such as G4 or F7, send those and we will match them. If you do not know the class, send the label of the filter you use now.

  3. 03

    Quantity

    How many of each size, and whether this is a one-off order or a regular one. A mixed list is fine, with one line per size.

  4. 04

    Application and airflow

    What the filter sits in, such as an air handling unit, a fan-coil unit, an oven or a cleanroom ceiling, and the airflow in cubic metres per hour if you have it. Add the temperature, the humidity and anything unusual in the air, such as grease, oil or chemicals.

A person checks every request. We tell you what matches, what differs and what we could not confirm, and we confirm the exact rating for your order.

Filter desk

Ask about high-temperature filters. A person replies.

The request form below is set to air filters and to this type. Give the size, the class and the quantity, add a photo of the old filter if you have one, and send it. A person reads every request, checks the details against the TAF range and replies by phone, WhatsApp or email.

Not sure this is the right type? Leave it as it is and say what the filter is for. We will tell you if another type fits better.

What do you need?

Send a part number or a photo of the rating plate. A person checks every request; this is not an automatic stock search.

Line stopped? Call first. We will pick up the request below too.

Robot part details
Rating plateoptional
Add a photo of the rating plateJPEG, PNG, WebP or HEIC, up to 8 MB.
More detail (optional)
Machining, cell or fixture details
Drawingoptional
Attach a drawingPDF, STEP, STP, DXF, DWG, PNG or JPG, up to 8 MB.
More detail (optional)
Air filter details
More detail (optional)

For example G4, F7 or H13.

Your details
Add a message

Files up to 8 MB. We use your details only to answer this request.

Questions

High-temperature filters: common questions.

What temperature rating do you offer?

The rating belongs to the product, so we do not quote one on this page. Send your continuous operating temperature and the peak if there is one, and we confirm the exact rating for your order before you commit. A filter should never be run above the rating that was confirmed in writing.

Can I use a standard filter in an oven supply?

Not if the air is hot enough to soften the frame, the glue or the gasket. A standard filter can distort, leak or burn. If the air is only slightly warm, a standard filter may do, but give us the actual temperature and we will tell you which side of the line you are on.

Are high-temperature filters also HEPA?

Some are available in high-efficiency classes, and others are for coarse or medium dust. The temperature and the efficiency class are two separate requirements. Tell us both: the operating temperature, and the class you need under ISO 16890 or EN 1822.

How do I measure the size?

Measure the opening or the housing seat in width, height and depth, in millimetres, and note how the filter is held and sealed. Photographs of the old filter and of the housing help. Oven housings are often custom, so be prepared to send a drawing.